ECONOMICS

1. Capitalized cost

2. Depreciation

1.Depreciation by Straight line method

2. Depreciation by Declining balance method

3. Depreciation by sum of the year digit method

4. Depreciation by sinking fund method

3. Maximum allowable pressure
1. Maximum allowable pressure Spherical container

4. Stress in cylindrical vessels
For cylindrical vessel circumferential stress is greater than longitudinal stress so it is taken as design stress

1. Circumferential stress (Hoop stress)

2. Longitudinal stress

5. Payback period

6. In case interest in calculated non-yearly time, total amount

7. Simple rate of return in investment

8. Present value of annuity at an interest rate i

9. Discounted value
Discounted value also called present value is the current worth of a future sum of money given a specified rate of return

10. Six-Tenth’s rule
Six-tenth’s rule for determining cost of equipment with different
capacity

11. Net present worth
Net present worth is defined as

12. Cost-Index rule

13. Payout period

14. Double declining method
For double declining method

Depreciation to be calculated year by year using f mentioned above

15. Blank diameter for tori spherical head
1. Thickness < 25mm/inch

2. Thickness > 25mm/inch

16.Nominal rate
Nominal rates in case rate is given per month or quarter or half yearly

17. Annuity
1. Relation between total amount (S), payments (R) i.e., annuity

2.Total amount of annuity, i.e., future worth of the accumulated
amount (S)

18. Turnover ratio and investment ratio
1. Turnover ratio

2. Investment ratio

19. Effective rate of interest
Effective rate of interest when interest rate is not defined on yearly basis

20. Total cost

21. Perpetuity

Perpetuity is a stream of identical cash flow with no end. Formula for determining present value of a perpetuity

2. Plant design and economics

1. Flanges

  • a. Narrow faced flanges is the one where all the face contact area lies within (inside) the circle enclosed by the bolt holes.
    b. In calculation of flange stress, the load acting on flanges are to be calculated for opening as well as for bolting up conditions and difference of the two will be taken.

2.Providing uniformly spaced internal or external stiffening rings may increase the rigidity of the cylindrical vessel subjected to internal or external pressure respectively.

3.Expansion joints are provided in fixed tube heat exchanger to reduce thermal stress in shell and tubes.

4. Unmortised cost = original value of equipment – total depreciation

5. Capitalized cost is used for comparing alternative investment choices.

6. A cylindrical shell under external pressure tends to buckle as a result of external radical pressure. The external pressure at which buckling occurs depends on modulus of elasticity, thickness of shell and diameter of the shell when length of shell is less than the critical length.

7.Unamortized value is used for replacement decisions and capitalized cost considering other investment choices

8.Breakeven point occurs when total annual product cost equals total annual sales, cumulative cash flow is zero.

9. Discounted cash flow is used in reference to payout period.

10. Torispherical head used for pressure less than 10 bar. Ellipsoidal head used for pressure greater than 10 bar. Hemispherical head is strongest.

11. Direct cost component of the fixed capital consists of onsite and offsite cost. Offsite cost is cost arising from a construction project that are spent in places other than construction site.

12. A cylindrical storage tank can have a self-supported conical roof if its diameter is more than 50m.

13. Whenever question asks to compare performance of an equipment before and after an MOC or investment, calculate capitalized cost to compare.

14. Circumferential stiffening rings are used to withstand higher external pressure.

15. Guy wire is used for external support.

16. Direct cost component of fixed capital consists of onsite and offsite costs.

17. A series of equal payments (e.g. deposits of cost) made at equal interval of time is known as annuity.

18. Fixed capital investment or total capital investment is product of Lang multiplication factor and delivered equipment cost.